search

Yamaha disklavier Mark II XG Series Manual de usuario Pagina 13

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 14
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 12
Chapter 3
Setting Up Your Disklavier
Set up your Disklavier in the following order.
Connecting the Control Unit
Make sure that the control cable extending from the piano is connected to the TO CONTROL CABLE FOR
PIANO connector on rear of the Control Unit.
Note: The control cable should have been connected to the Control Unit when the Disklavier was
installed. If, however, it was not, carefully connect the control cable to the Control Unit’s TO
CONTROL CABLE FOR PIANO connector on the rear panel. See step (4) in “Mounting the
Control Unit to the Grand Piano” in the front of this manual.
The Control Unit may be placed on any stable surface on, neai; or away from the Disklavier as far as the
length of the cable will permit.
For the Disklavier grand, the Control Unit may be mounted to the underside of the treble side key bed. See
“Mounting the Control Unit to the Grand Piano” at the front of this manual.
Connecting the Power Cable
Connect the Disklavier’s power cable to an AC wall outlet.
Important: Make sure that the voltage of the AC wall outlet matches that marked on the Disklavier's
Serial No. plate.
Connecting a Speaker System
To enjoy Ensemble songs, connect powered speakers to the Disklavier’s OUTPUT terminals, as shown on the
next page. You can also use a separate amplifier with speakers. If your sound system is mono, use only the
L/MONO connector for the best sound.
12 Chapter 3 : Setting Up Your Disklavier
These are powered
speakers with built-in
amplifiers
(not supplied)
Connecting Other Equipment
To connect MIDI instruments to the Disklavier, see Chapter 8 “The Disklavier & MIDI” in the Advanced
Operation Manual.
To connect a computer to the Disklavier, see Chapter 9 “The Disklavier & Computers” in the Advanced
Operation Manual
Power On Procedure_____________________________________
Set the MAINS switch to ON.
Press the [STANDBY - ON] button on the front panel of the Control Unit.
The following message appears on the display.
........ t J,***. 1. .1 I.”’. t
ri.-'M r'i! ! T !!!!'!"!'
Connecting Other Equipment 13
Vista de pagina 12
1 2 ... 8 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Los dispositivos de entrada Yamaha disklavier Mark II XG Series
Los dispositivos de entrada Yamaha PortaSound PSS-21 Manual de usuario    (14 paginas)
Los dispositivos de entrada Yamaha Portatone PSS-140 Manual de usuario      (31 paginas)
Los dispositivos de entrada Yamaha Portatone PSR-11 Manual de usuario      (20 paginas)
Los dispositivos de entrada Yamaha Personal Electronic Piano YPP-15 Manual de usuario   (20 paginas)
Los dispositivos de entrada Yamaha PortaSound PSS-580 Manual de usuario   (29 paginas)
Los dispositivos de entrada Yamaha GranTouch Manual de usuario   (22 paginas)
Los dispositivos de entrada Yamaha PLG100-VH Manual de usuario   (32 paginas)
  • BabyCargo NewAir MegaPro RAD Data comm Earthwase
  • Intenso Las Unidades Flash Usb Husqvarna Rociador de pintura Epson Herramientas Eléctricas OmniMount Gradas de equipos AV HP Adaptadores E Inversores De Energía
  • HP EliteDesk 800 G4 Tower PC Sony DAV-DZ860W Epson ActionLaser 1000 Samsung GT-I9103 TAFCO WINDOWS NU2-3214IS
  • Samsung S20B300B Manual de usuario Peavey Ultra Plus Manual de usuario Zoom Thunderbolt TAC-2 Especificaciones AEG L6227FL Manual de usuario Sharp PN-V602 Manual de usuario