Yamaha PLG100-XG Manual de usuario descargar pdf (Pagina 30)

MIDI Data Format

2.1.3 XG parameter change

This message sets XG-related parameters. Each message can set a single

parameter.

The message format is as follows.

11110000 F0H Exclusive status

01000011 43H YAMAHA ID

0001nnnn 1NH N:device Number

01001100 4CH Model ID

0ggggggg GGH Address High

0mmmmmmm MMH Address Mid

0lllllll LLH Address Low

0sssssss SSH Data

: :

11110111 F7H End of Exclusive

For parameters whose Data Size is 2 or 4, the appropriate amount of data

will be transmitted as indicated by Size.

2.1.3.1 XG System On

11110000 F0H Exclusive status

01000011 43H YAMAHA ID

0001nnnn 1NH N:device Number

01001100 4CH Model ID

00000000 00H Address High

00000000 00H Address Mid

01111110 7EH Address Low

00000000 00H Data

11110111 F7H End of Exclusive

When On is received, the SOUND MODULE MODE will be set to XG.

Since approximately 50[ms] are required in order to execute this message,

please allow an appropriate interval before transmitting the next message.

2.1.3.2 XG System parameter change

This message sets the XG SYSTEM block (refer to tables <1 -1>, <1 - 2>).

2.1.3.3 Multi Effect1 parameter change

This message sets the MULTI EFFECT1 block (refer to tables <1 - 1>,

<1 - 3>).

2.1.3.4 Multi Part parameter change

This message sets the MULTI PART block (refer to tables <1 - 1>, <1 - 4>).

2.1.3.5 Drums Setup parameter change

This message sets the DRUMS SETUP block (refer to tables <1 - 1> , <1 - 5>).

2.1.4 Other parameter changes

2.1.4.1 Master tuning

This message simultaneously modiﬁes the tuning of all channels.

11110000 F0H Exclusive status

01000011 43H YAMAHA ID

0001nnnn 1NH N:device Number

00100111 27H Model ID

00110000 30H Address High

00000000 00H Address Mid

00000000 00H Address Low

0000mmmm 0MH Master Tune MSB

0000llll 0LH Master Tune LSB

0xxxxxxx XXH don't care

11110111 F7H End of Exclusive

Normally, the XG SYSTEM message MASTER TUNE should be used

(refer to table <1-2>).

2.2 Bulk dump

This device uses the following bulk dump messages.

[XG BULK DUMP]

1) XG System bulk dump

2) Multi Effect1 bulk dump

3) Multi Part bulk dump

4) Drums Setup bulk dump

2.2.1 XG bulk dump

This message sets XG-related parameters. Unlike parameter change messages,

a single message can modify multiple parameters. The message format is as

follows.

11110000 F0H Exclusive status

01000011 43H YAMAHA ID

0000nnnn 0NH N:Device Number

01001100 4CH Model ID

0sssssss SSH ByteCountMSB

0ttttttt TTH ByteCountLSB

0ggggggg GGH Address High

0mmmmmmm MMH Address Mid

0lllllll LLH Address Low

0vvvvvvv VVH Data

: :

0kkkkkkk KKH Check-sum

11110111 F7H End of Exclusive

Address and Byte Count are given in tables 1-n. Byte Count is indicated by

the total size of the Data in tables 1-n.

Bulk dump and dump request messages are received when the beginning

of the block is speciﬁed as the 'Address'.

'Block' indicates the unit of the data string that is indicated in tables 1-n as

'Total size'.

Check sum is the value that produces a lower 7 bits of 0 when the Start

Address, Byte Count, Data, and the Check-sum itself are added.

2.2.1.1 XG System bulk dump

This message sets the XG SYSTEM block (refer to tables <1 -1>, <1 - 2>).

2.2.1.2 Multi Effect1 bulk dump

This message sets the MULTI EFFECT1 block (refer to tables <1 - 1>,

<1 - 3>).

2.2.1.3 Multi Part bulk dump

This message sets the MULTI PART block (refer to tables <1 - 1>, <1 - 4>).

2.2.1.4 Drums Setup bulk dump

This message sets the DRUMS SETUP block (refer to tables <1 - 1>, <1 - 5>).

3. Realtime messages

3.1 Active sensing

a) Transmission

not transmitted.

b) Receive

Once FE has been received, failure to receive any MIDI message for an

interval longer than approximately 300 msec will cause processing to

be performed as if ALL SOUND OFF, ALL NOTE OFF, and RESET

ALL CONTROLLERS messages were received, and the unit will reset

to a condition in which FE was never received.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 41 42

Comentarios a estos manuales

Sin comentarios

Yamaha PLG100-XG Manual de usuario Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Los dispositivos de entrada Yamaha PLG100-XG